Pinout — AD9850 DDS Signal Generator Module

Pin	Señal	Descripción
`ZOUT2`	analog	Sine-wave DDS analog output from the AD9850 output network.
`ZOUT1`	analog	Sine-wave DDS analog output from the AD9850 output network.
`QOUT2`	digital	Square-wave comparator output derived from the DDS sine signal.
`QOUT1`	digital	Square-wave comparator output derived from the DDS sine signal.
`GND`	ground	Ground reference for power, logic control, and output signals.
`RESET`	reset	AD9850 reset control input; use to initialize the DDS state.
`DATA`	data	Serial programming data input for loading frequency and control words.
`FU_UD`	digital	Frequency update strobe; latches loaded tuning word into the DDS.
`W_CLK`	clock	Serial word clock input for shifting programming data into the AD9850.
`VCC`	power	Module power input, typically 5 V for AD9850 operation.
`GND.1`	ground	Ground reference for power, logic control, and output signals.
`D7`	data	Parallel programming data bus bit 7 input for the AD9850.
`D6`	data	Parallel programming data bus bit 6 input for the AD9850.
`D5`	data	Parallel programming data bus bit 5 input for the AD9850.
`D4`	data	Parallel programming data bus bit 4 input for the AD9850.
`D3`	data	Parallel programming data bus bit 3 input for the AD9850.
`D2`	data	Parallel programming data bus bit 2 input for the AD9850.
`D1`	data	Parallel programming data bus bit 1 input for the AD9850.
`D0`	data	Parallel programming data bus bit 0 input for the AD9850.
`VCC.1`	power	Module power input, typically 5 V for AD9850 operation.

Notas de cableado

Alimenta el módulo con 5V (VCC) y GND. Control serie (recomendado, 4 líneas): W_CLK (word clock), FQ_UD (frequency update / latch), DATA (datos serie) y RESET, cada una a un pin digital libre del microcontrolador. Ojo: en este módulo el pin de actualización está rotulado como FU_UD (= FQ_UD). Como alternativa, se puede usar el bus paralelo de 8 bits D0-D7 más W_CLK/FQ_UD/RESET. Salidas: ZOUT1/ZOUT2 entregan la senoide, QOUT1/QOUT2 la salida cuadrada/comparador. El módulo tiene su propio reloj de referencia de 125 MHz; no se necesitan componentes externos de protección para placas de 5V. En una placa de 3,3V (ESP32/ESP8266), conecta las líneas de control mediante un level shifter.

Esquema de cableado de ejemplo — AD9850 DDS Signal Generator Module

Desde	Hasta	Cable
`board:5V`	`x1:VCC`	red
`board:GND`	`x1:GND`	black
`board:D8`	`x1:W_CLK`	green
`board:D9`	`x1:FU_UD`	blue
`board:D10`	`x1:DATA`	yellow
`board:D11`	`x1:RESET`	purple

Código Arduino de ejemplo — AD9850 DDS Signal Generator Module

Este ejemplo se escribió y verificó por compilación para arduino-uno. Codey Online lo adapta a cualquier otra placa compatible.

// Canonical beginner example for the AD9850 DDS Signal Generator Module
// This sketch sends a serial programming word to set an output frequency.
// Wiring used:
//   D8  -> W_CLK
//   D9  -> FU_UD
//   D10 -> DATA
//   D11 -> RESET
//   5V  -> VCC
//   GND -> GND

const int PIN_W_CLK = 8;
const int PIN_FQ_UD = 9;   // Module label is FU_UD
const int PIN_DATA  = 10;
const int PIN_RESET = 11;

const unsigned long CLOCK_HZ = 125000000UL; // AD9850 reference clock on the module

void pulsePin(int pin) {
  digitalWrite(pin, HIGH);
  delayMicroseconds(1);
  digitalWrite(pin, LOW);
  delayMicroseconds(1);
}

void ad9850Reset() {
  digitalWrite(PIN_RESET, HIGH);
  delayMicroseconds(1);
  digitalWrite(PIN_RESET, LOW);
  delayMicroseconds(1);
  pulsePin(PIN_W_CLK);
  pulsePin(PIN_FQ_UD);
}

void ad9850SetFrequency(double frequencyHz) {
  // DDS tuning word = frequency * 2^32 / clock
  uint32_t tuningWord = (uint32_t)((frequencyHz * 4294967296.0) / (double)CLOCK_HZ);

  // Send 32-bit tuning word, LSB first
  for (int i = 0; i < 32; i++) {
    digitalWrite(PIN_DATA, (tuningWord >> i) & 0x01);
    pulsePin(PIN_W_CLK);
  }

  // Control byte: 0x00 for normal 28-bit frequency mode
  for (int i = 0; i < 8; i++) {
    digitalWrite(PIN_DATA, LOW);
    pulsePin(PIN_W_CLK);
  }

  // Latch the new frequency
  pulsePin(PIN_FQ_UD);
}

void setup() {
  pinMode(PIN_W_CLK, OUTPUT);
  pinMode(PIN_FQ_UD, OUTPUT);
  pinMode(PIN_DATA, OUTPUT);
  pinMode(PIN_RESET, OUTPUT);

  digitalWrite(PIN_W_CLK, LOW);
  digitalWrite(PIN_FQ_UD, LOW);
  digitalWrite(PIN_DATA, LOW);
  digitalWrite(PIN_RESET, LOW);

  Serial.begin(9600);
  while (!Serial) {
    ;
  }

  Serial.println(F("AD9850 DDS generator starting..."));
  ad9850Reset();

  // Set a beginner-friendly test frequency
  ad9850SetFrequency(1000000.0); // 1 MHz
  Serial.println(F("Output frequency set to 1 MHz"));
}

void loop() {
  // Nothing to do here for the canonical example.
  delay(1000);
}