Codey Online › Biblioteka komponentów Arduino i ESP32 › Micro-SD Card Reader 3.3V
Micro-SD Card Reader 3.3V
Pamięć

Micro-SD Card Reader 3.3V

To jest moduł czytnika kart microSD 3,3V, który umożliwia mikrosterownikowi komunikację z kartą microSD przez magistralę SPI. Używa CS (chip select) razem z MOSI, MISO i CLK oraz współdzieli GND i zasilanie 3,3V z systemem.

Szerokość: 21.2 mm

Pinout — Micro-SD Card Reader 3.3V

Pin Sygnał Opis
3V3 power 3.3V power input for the microSD card reader; use only 3.3V logic/power.
CS chip-select SPI chip-select input for the microSD card; active low.
MOSI MOSI SPI data from host MCU to microSD card.
CLK SCK SPI clock input from the host MCU to the microSD card.
MISO MISO SPI data output from microSD card to host MCU.
GND ground Ground reference for power and SPI signals.

Przykładowy schemat połączeń — Micro-SD Card Reader 3.3V

Z Do Przewód
board:5V x1:3V3 red
board:GND x1:GND black
board:D10 x1:CS green
board:D11 x1:MOSI blue
board:D13 x1:CLK yellow
board:D12 x1:MISO purple

Przykładowy kod Arduino — Micro-SD Card Reader 3.3V

Ten przykład został napisany i sprawdzony kompilacją dla arduino-uno. Codey Online dostosuje go do każdej innej obsługiwanej płytki.

#include <SPI.h>
#include <SD.h>

const int SD_CS_PIN = 10;

void setup() {
  Serial.begin(9600);
  while (!Serial) {
    ;
  }

  Serial.println("Micro-SD Card Reader 3.3V example");
  Serial.println("Initializing SD card...");

  pinMode(SD_CS_PIN, OUTPUT);
  digitalWrite(SD_CS_PIN, HIGH);

  if (!SD.begin(SD_CS_PIN)) {
    Serial.println("SD card initialization failed!");
    Serial.println("Check wiring, card format, and that the module is powered correctly.");
    while (true) {
      delay(1000);
    }
  }

  Serial.println("SD card initialized successfully.");

  File root = SD.open("/");
  if (root) {
    Serial.println("Files on the card:");
    printDirectory(root, 0);
    root.close();
  } else {
    Serial.println("Could not open root directory.");
  }
}

void loop() {
  // Simple periodic status message so you can see the sketch is running.
  Serial.println("SD card ready.");
  delay(2000);
}

void printDirectory(File dir, int numTabs) {
  while (true) {
    File entry = dir.openNextFile();
    if (!entry) {
      break;
    }

    for (int i = 0; i < numTabs; i++) {
      Serial.print('\t');
    }

    Serial.print(entry.name());
    if (entry.isDirectory()) {
      Serial.println("/");
      printDirectory(entry, numTabs + 1);
    } else {
      Serial.print("\t");
      Serial.println(entry.size(), DEC);
    }

    entry.close();
  }
}

Podobne komponenty

Micro-SD Card Reader 5V

Micro-SD Card Reader 5V

Micro SD Card Adapter Module 3.3V

Micro SD Card Adapter Module 3.3V

RFID RC522 Module 13.56MHz

RFID RC522 Module 13.56MHz

1.28" Round TFT LCD 240x240 (GC9A01, SPI)

1.28" Round TFT LCD 240x240 (GC9A01, SPI)

Zbuduj swój projekt Arduino lub ESP32 z pomocą AI

Opisz, co chcesz zbudować. Codey Online napisze kod, narysuje schemat połączeń, skompiluje projekt i wgra go na płytkę bezpośrednio z przeglądarki.

Zacznij za darmo